Electronics connectors have evolved from simple wire-to-wire interface components to those capable of transferring enormous volumes of data required for applications such as video and autonomous driving. Connectors are also being exposed to more demanding environmental conditions such as liquids, noxious gases, extreme temperatures, mechanical shock, and vibration. In order to improve reliability and longevity, many industries including aerospace and automotive have chosen to include flexible thermoplastic gel-pads in designs.
The properties of Resin Designs’ gel-pads make them excellent candidates for sealing electrical connectors. However, in any sealing application, the seal and the item being sealed are a system and cannot be treated independently. This is also the case with gel seals for electrical connectors. The seal and the connector must be compatible and work together to achieve adequate sealing.
The following are some basic guidelines for the types of connectors that are best suited to gel-pad protection. For a more detailed discussion and analysis please visit the link below.
Gels combine two effects to create a seal. First, under compression, gels can conform around a variety of objects, such that the surface of the gel is in contact with the entire surface of the object to be sealed. Once the surfaces are in contact, the thermodynamics of the system favors the coating of the surface by the gel versus by air or water. This allows the gel to seal against air and water. It is the combination of the gel's ability to conform around a surface as well as to coat (or wet) the surface that allows it to seal. One effect without the other would not be useful.
A single gel composite seal is used to seal all contact cavities in a connector. They are not used as individual wire seals. Although a gel composite seal will appear to be a solid piece, it is pre-cut at each position where a contact will be inserted. This minimizes the contact insertion force.
The gel grommet seal must be contained and put under pressure to create a seal. A seal recess is required at the rear of the connector to hold the gel seal. The seal recess must fully contain the sides of the gel seal, as this is the primary sealing interface. Compression is applied to the gel by the use of a cap that locks onto the rear of the connector. The gel seal will be compressed between the bottom surface of the connector seal recess and the compression cap. The gap between the bottom surface of the connector seal recess and the compression cap must be designed and controlled to apply the proper amount of compression to the gel.
Contacts are inserted and removed through the gel seal. It is normal for the contacts to pick up gel during insertion and removal. Extensive testing has been done to verify that the gel on the contacts does not impact the electrical performance. Neither the initial contact resistance nor the long-term contact resistance is adversely affected by the presence of gel.
Gel grommets are stamped from sheet stock. The normal delivery method is to provide pre-cut parts on a continuous mylar backing on reels. Other delivery methods to suit the customer’s handling needs could be examined.
No material is a universal solution. Gels are not the best sealing solution in all cases. The following charts outline a few of the application features characterized within the automotive connector market. The ability of the gel to seal any given application is characterized by its compatibility with these application features, among others. Here, we will limit our explanation to the areas of “contact type” and “connector type.” Again, for a more detailed discussion of additional factors please refer to the link above.
| Connector Type | Gel Seal Compatibility |
| Cylindrical | Best - Usually smooth and well-rounded. |
| Box (Lance-less) | Good - Most are acceptable for use with gel seals. There is a lot of variation in box contact designs. Some are well-rounded and some have sharp edges. |
| Lanced | Varies - Generally aggressive -- mainly during extraction. Smaller sizes are more acceptable than larger ones. |
| Cable to Cable | A lot is gained by small size and high density on high-contact count connectors. |
| Box Interface | Full range of sizes from a few contacts in a sensor to high contact counts in major electronics. Size and density are important. |
| Firewall and High Wire Count Cable to Cable | Medium to high contact count. Size and density are important. |
The following is a list of the basics to be used to analyze your project and the suitability of gel pads for sealing and protection.
Silicone gel pads present designers of electrical connectors with unique properties for increased protection and longevity. However, not all connectors are well suited to the use of gel-pad connectors, and it is important to design using the guidelines noted within this presentation to reap the full benefits of gel-pad protection.
As a supplier of electronics protection polymers and coatings, Chase Corporation and its employees can help you with an unbiased approach to evaluating your application and process. We’ll show you how to maximize efficiency, minimize cost, and improve product reliability. Our outstanding manufacturing and technical support groups can provide your organization with reliable global supply, unmatched quality, and superior technical support.